Bloomfield 8572 Especificaciones descargar pdf (Pagina 11)

F. REPLACE HEATING ELEMENT

1. Remove tank lid assembly per section D.

2. Remove two hex nuts holding element to cover.

Pull element from mounting holes.

3. Reassemble in reverse order.

IMPORTANT: When replacing heating elements,

also replace seal gaskets.

G. REPLACE READY LIGHT, WARMER SWITCH or

BREW BUTTON.

1. Unplug power cord or turn circuit breaker OFF.

2. Using Switch Removal Tool (p/n 83209) or a thin

screwdriver, pry light or switch from mounting

hole. Disconnect leads.

3. Reassemble in reverse order.

H. REPLACE OLD STYLE SOLENOID

1. Unplug power cord or turn circuit breaker OFF.

2. Turn OFF and disconnect water supply.

3. Remove water connection and hex nut holding inlet

fitting into back of brewer.

4. Remove two screws holding access door in place.

Remove access door.

5. On faucet models, remove flare connection from

"tee" inlet fitting.

6. Push solenoid forward slightly and lift to release it

from bracket. Carefully pull solenoid out thru

access hole.

7. Remove wiring and rubber tubing from solenoid.

8. Remove fittings from old solenoid and transfer to

new solenoid.

9. If necessary, replace flow control at this time. 10.

Reassemble in reverse order.

I. REPLACE NEW STYLE SOLENOID

1. Unplug power cord or turn circuit breaker OFF.

2. Turn OFF and disconnect water supply.

3. Remove two screws holding solenoid door in

place. Remove access door. Remove solenoid.

4. Remove hose(s) from solenoid. Remove wiring

from solenoid.

5. Reassemble in reverse order.

J. REPLACE TIMER ASSEMBLY

1. Unplug power cord or turn circuit breaker OFF.

2. Remove front panel. Remove knob and three

screws holding timer to bracket. Disconnect

wiring to timer.

3. Reassemble in reverse order.

4. Adjust timer per Section B.

K. REPLACE WARMER ELEMENT

1. Unplug power cord or turn circuit breaker OFF.

2. Turn warmer plate counter-clockwise until it

unscrews from bracket.

3. Lift element off bracket. Disconnect leads.

4. Reassemble in reverse order.

L. CLEAN SPRAY HEAD

1. Remove brew chamber.

2. Rotate spray disk out of spray head by pushing

up and rotating it out of locking grooves.

3. Clean off lime build-up and wipe oil from both

sides of spray disk. Make sure all holes in spra^

disk are fully open.

4. Clean entire area over brew chamber with a

damp cloth.

5. Replace spray disk, being sure spray head

gasket is in place INSIDE cup. Spray disk tabs

must be in the UP position. Rotate spray disk

fully into locking grooves.

WATER FLOW

A. KOFFEE-KING™ POUR-OVER (ALL MODELS)

Pouring any amount of cold water into basin pan

forces an identical amount of hot water out of tank

and thru spray head.

B. KOFFEE-KING™ AUTOMATIC MODELS 8540,

8541, 8572, 8573 and 8574

Pressing BREW button energizes solenoid valve,

allowing water to flow into basin pan and then into

hot water tank. Length of time solenoid is open is

controlled by timer.

C. KOFFEE-KING™ FAUCET MODELS 8540,

8572 and 8574

Faucet water coil is submerged in hot water tank

and draws heat from brew water. Water going to

water coil is not controlled by solenoid valve.

Faucet is at supply water pressure any time faucet

shut-off valve is OPEN.

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 17

Comentarios a estos manuales

Sin comentarios

Bloomfield 8572 Especificaciones Pagina 11

Comentarios a estos manuales

Relacionado con productos y manuales para Cafeteras Bloomfield 8572